[SOLVED] Crossfader gets ignored

[Fant0m]

Hi i am new here

i got 2 stanton t.62 a Numark dm950 mixer and mixvibes DVS. Mixvibes gets a perfekt timecode signal everything is fine except that it ignores the crossfader of my mixer. I would like to hear one deck on the monitor and the other on my headphones controlling it with the crossfader for my headophone. thanks in advance!

Best regards

[UncleVibes]

publish a config report...

[Fant0m]

Config Report:

Config 2010/01/26 22:54

OS=Microsoft Windows XP Service Pack 3 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 15 Stepping 13, GenuineIntel
MixVibes Producer version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=No
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=3
TAG V1=Yes TAG V2=No

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=Maya44 USBAudio ASIO driver AsioVersion=0 DriverVersion=34081536
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=4
Managment Type ASIO
1-OUT 0 - Maya44 2-OUT 1 - Maya44
3-OUT 2 - Maya44 4-OUT 3 - Maya44

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:IN 0 - MAYA44 USB-IN 1 - MAYA44 USB
Mode=all relative
Riaa=Yes Preamp Left=29 db Preamp Right=27 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=Yes
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:IN 2 - MAYA44 USB-IN 3 - MAYA44 USB
Mode=all relative
Riaa=Yes Preamp Left=29 db Preamp Right=27 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl 3 not connected
Vinyl 4 not connected

[Support@MixVibes]

You should set both decks in the software to [01], and put the monitor dot in the sound configuration to outputs 3&4.
Then activate the cue headphone on the deck you wan to route to [02]

Now your main is [01] aka 1&2
et your monitor/headphone cue is [02] aka 3&4.

[Fant0m]

Thanks for your replay. I put both decks on 01 and if i now click on the headphones i can listen to the second deck which is not to hear on monitor. But is there now possibility that i can crossfade and listen to the next song with my mixer? do i always have to click the headphones button and crossfade in mixvibes?

[Fant0m]

Nevermind i solved it by trying and error

thanks again

[Support@MixVibes]

Yes because this is not a regular setup : you asked to have the crossfader between air<|>headphone

With a regular setup each deck have it own channels, and the crossfader is for what is on air (not the headphone).
It would look like deck1<|>deck2 and all the headphone part is done on the mixer not in the software.

[moedaroller]

Nevermind i solved it by trying and error

thanks again

how did you fix it? got same problem

[phadedvision]

Nevermind i solved it by trying and error

thanks again

how did you fix it? got same problem

Hi moedaroller,

Fant0m's using a different version of MixVibes than you are, but this should point you more in the right direction: viewtopic.php?f=207&t=16080