Problem Stop

[whitelion]

I've installed teh new DVS version 7.1 but when i stop vynil... the cusor on waveform continues to move near where i stop ... so i can't cue ..

(excuse me for my bad english)

[N-deep]

Did you check the needles? What driver version do you use? Moreover can you post a config report file?

[Macgyver]

I've installed teh new DVS version 7.1 but when i stop vynil... the cusor on waveform continues to move near where i stop ... so i can't cue ..

(excuse me for my bad english)

Sounds like one of 2 things.

1) A noise issue, what sound card are you using?

or

2) a problem that i mentioned in one of my earlier posts regarding a drift of the cue marker when using the MIDI controller. I believe another user mentioned having the same problem with vinyl as well.

http://forum.mixvibes.com/viewtopic.php?f=308&t=10638

[whitelion]

with the previus version it work well... i don'think is an hardware problem...

[polocorp]

hi whitelion, did you overwrite your previous version ? It's advised to install in a new folder to avoid confilcts in overwriting (and be able to go back to the previous version if necessary)

[whitelion]

the problam is in "all relative mode" of 7.10 (i've installed te 7.33 in another folder and works good)
i use U46DJ driver v1_039

this is mi config report

Config Report:

Config 2008/11/27 22:29

OS=Microsoft Windows XP Service Pack 2 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 13 Stepping 8, GenuineIntel
MixVibes DVS version=7.100 DLL langage=US version=7.100

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=ASIO 2.0 - ESI U46 AsioVersion=0 DriverVersion=2
Latency=3 Driver sampling=44100 Nb Input=4 Nb Output=6
Managment Type ASIO
1-L:U46DJ 1/2 2-R:U46DJ 1/2
3-L:U46DJ 3/4 4-R:U46DJ 3/4

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:L:U46DJ 1/2-R:U46DJ 1/2
Mode=all relative
Riaa=No Preamp Left=4 db Preamp Right=2 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=Yes
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=89.665 Volume max left=0.376 Volume max right=0.349 Volume optimum=0.370
Speed Average(100ms)=1.001 Speed Average(1s)=1.001 Speed Average(3s)=1.001


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:L:U46DJ 3/4-R:U46DJ 3/4
Mode=all relative
Riaa=No Preamp Left=3 db Preamp Right=4 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.407 Volume max right=0.415 Volume optimum=0.370
Speed Average(100ms)=1.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000

another problem is that when i use mixvibes in all relative mode the time code percent goes to 0 (this in the 7.33 too but it givese no problem)

[whitelion]

ideas??

[UncleVibes]

another problem is that when i use mixvibes in all relative mode the time code percent goes to 0 (this in the 7.33 too but it gives no problem)

This is normal, the absolute counter isn't in use. Phono must be set to on instead of off, you use a sound card with riaa preamp (see vinyl options).

[bigibang]

watch this video, and tell me if it's your bug.

[whitelion]

yes is the same problem i have...
but i'm ftom italy and i cant read the solution .. how to fix

(the problem remains sitching off preamp setting)