High tones vibrating with vinyl

[FredrikH]

I have been running Mix Vibes DVS for almost a year now and didnt notice this until just now. When I change between using the timecoded vinyls and just running the players on the screen the sound is different. With the vinyls there is a slight vibration in the higher tones, especially if its a long dragged out tone its clearly noticable. When I switch over to use the on screen players the bibration is gone. I have recently bought a new mixer but that cant be the cause since the on scren players also go through the mixer. The turntables are regular Technics 1210 MK2 with Ortofone concord. There is no vibrating sound when I plar regular vinyls. What can be the cause? I am sure it wasnt sounding like that a few weeks ago because I would have noticed.

best regards,
Fredrik Hagblom

[gravel]

Hi!

I have the samekind of problem. It sounds like someones moving the pitch slider up and down. :S

And sometimes it sounds like the record stops.

Heres my config:

Config Report:

Config 2008/07/22 19:19

OS=Microsoft Windows XP Service Pack 3 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 15 Model 76 Stepping 2, AuthenticAMD
MixVibes DVS version=6.411 DLL langage=US version=6.290

System Setting
--------------------
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=0
Windows Moveable=No
TAG V1=Yes TAG V2=No

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=MIXVIBES U46MK2 ASIO AsioVersion=0 DriverVersion=2
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=6
Managment Type ASIO
1-L:U46DJ 1/2 2-R:U46DJ 1/2
3-L:U46DJ 3/4 4-R:U46DJ 3/4

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:L:U46DJ 1/2-R:U46DJ 1/2
Mode=Absolute
Riaa=Yes Preamp Left=3 db Preamp Right=2 db Noise Filter=0
45T=No InverseLR=No PhaseInv=No
Offset=0 ms
Noise Level=-40.000 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.332 Volume max right=0.322 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:L:U46DJ 3/4-R:U46DJ 3/4
Mode=Absolute
Riaa=Yes Preamp Left=5 db Preamp Right=5 db Noise Filter=0
45T=No InverseLR=No PhaseInv=Yes
Offset=0 ms
Noise Level=-40.000 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.362 Volume max right=0.373 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000

regards,
Karl Oksanen

[N-deep]

Hi,

Did you update to the latest version of MixVibes?

[polocorp]

hi there, both of you should enter your serial number into your profil. this will allow you to access the updates in the download center...

which mode do you spin in ? Absolute, relative ? Do you use the master tempo ?