Crossfader channel settings

[Fant0m]

Hi,

I got the following problem. I got a new Mixer -> Numark M2. The problem is that if i move the Crossfader to all the way to the left i hear the left turntables full volume both channels and if i move it to the right i still hear it only on one channel. If i move it to the right its the other way around. I didnt change anything on my setup but the mixer and with my old mixer it worked fine.

Thanks in advance

Best regards

Fant0m

[hemskoc]

Have you pressed the channel selector by accident?
On the screen, Is the left deck routed to '1' and the right deck routed to '2' (selection box on the lower right of each 'player')?
Cheers

[Fant0m]

Thanks for the fast answer. I checked the channel selector and left deck is 1 and right deck 2 just how it is supposed to be. Any other suggestions?

Best regards

[Soreno]

Try to have a look on the monitoring on the player MV

[Fant0m]

Thanks for your reply.
What exactly do you mean by that?

Try to have a look on the monitoring on the player MV

I didn't change any setting in mixvibes and with my old mixer everything worked fine.

[Soreno]

Look if on your player this little headphones are highlight or not ? And look about the output

[Fant0m]

I checked both. Output is set right and if i highlight the headphones nothing changes. i add a conig report.



Config 2010/04/24 16:44

OS=Microsoft Windows XP Service Pack 3 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 15 Stepping 13, GenuineIntel
MixVibes Producer version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=3
TAG V1=Yes TAG V2=No

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=50 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=Maya44 USBAudio ASIO driver AsioVersion=0 DriverVersion=34081536
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=4
Managment Type ASIO
1-OUT 0 - MAYA44 USB 2-OUT 1 - MAYA44 USB
3-OUT 2 - MAYA44 USB 4-OUT 3 - MAYA44 USB

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:IN 0 - Maya44-IN 1 - Maya44
Mode=all relative
Riaa=Yes Preamp Left=28 db Preamp Right=27 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.666 Volume max right=0.666 Volume optimum=0.370
Speed Average(100ms)=0.033 Speed Average(1s)=0.032 Speed Average(3s)=0.033


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:IN 2 - Maya44-IN 3 - Maya44
Mode=all relative
Riaa=Yes Preamp Left=28 db Preamp Right=27 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=90.075 Volume max left=0.704 Volume max right=0.704 Volume optimum=0.370
Speed Average(100ms)=1.001 Speed Average(1s)=1.000 Speed Average(3s)=1.001


Vinyl 3 not connected
Vinyl 4 not connected

[Marxon]

Hi Fant0M!

and if i move it to the right i still hear it only on one channel. If i move it to the right its the other way around.

You talked twice about the right side of your crossfader....
If you didit make any changes in your Settings then your problem is the mixer.
Do you mean your Master Output or your Headphones?
Your Mixer has two cue modes. Did you turned it to CH1-Ch2 Mode?

greatz Marxon

[Fant0m]

Its my master and my record output. Both act the smae way. As long as i have only one cinch calbe connected to the master/record out, the crossfader works fine. If i have both cables connected and play for example a song on the right turntable and turn my crossfader to the left i still hear the left output of the right turntable. The result is a more quite and only on one Speaker hearable sound of the right turntable even tough you shouldnt hear anything of it at all.

[Support@MixVibes]

Crossfader bleeding ?
When the crossfader is in the center and if you ONLY use the faders, do you still have the issue ?