mapping out and dysfunction with modifiers

[tonip]

Thanks for sending and the time spent , the vu-meter runs but does not respond properly to the volume , ok for pfl channels ABCD . I have a problem : I press the kill- low A, step C , I press the kill- low C , I go back to A and nothing works , buttons and faders blocked idem in C. mixer off and on , ok . It would be good to do a kind of led_reset when going from A to C

[FigDJ]

Thanks for sending and the time spent , the vu-meter runs but does not respond properly to the volume , ok for pfl channels ABCD . I have a problem : I press the kill- low A, step C , I press the kill- low C , I go back to A and nothing works , buttons and faders blocked idem in C. mixer off and on , ok . It would be good to do a kind of led_reset when going from A to C

OK I understand. Do you have the same problem with the BD side?
if you don't, then please try the file posted below.
If you do have the same problem with the BD side, do not use this file. Just let me know.

Please explain more about the VU meter not responding properly to volume.

There is a switch for PFL and master. I have not mapped the master vu meter yet.

mixer one(Dj-Tech)Mod2.mappings

[tonip]

The Vu - meter has led to always on one flashes , the LEDs do not have a rocking motion with the music . The problem A to C I did other tests , you are no longer locked , mah

[FigDJ]

The Vu - meter has led to always on one flashes , the LEDs do not have a rocking motion with the music . The problem A to C I did other tests , you are no longer locked , mah

please verify
The switching between A and C
The switching between B and D

They both work correctly?
If so then moving on to the VU meters

Using a command like this
<mapping>
<control alias="fam(Mixer).ChannelAMeter" value="%"/>
<MIDI type="CC" parameter="0x22" channel="0x6" value="%"/>
</mapping>

This command is set up to take the output of Cross from the Channel and make the LED follow whatever value is send by Cross.

This particular Mixer/controller works like this.

from values
0-11=All LEDs off
12-23= 1 LED on
24-35= 2 LEDs on
36-47= 3 LEDs on
48-59= 4 LEDs on
60-71= 5 LEDs on
72-83= 6 LEDs on
84-95= 7 LEDs on
96-107= 8 LEDs on
108-119= 9 LEDs on
120-127= All LEDs on

That is just the way this controller is wired to respond and there is not much I can do about it.

If the answer to my question at the beginning of this post is that it does work, then I will move to map the Master VU-meter.

Did you tested using Mod1 file or Mod2 file?

I will need your help testing because I have to guess the correct channel.
let me know.

[tonip]

switches A / C and B / D work ok . I'm trying mod2 . Even for the vu-meter must configure the various modifiers ? I read that there are four configuration modes vu-meter ( I can not find examples )

[FigDJ]

switches A / C and B / D work ok . I'm trying mod2 .

OK, just to be clear. Once again, all switching works using Mod2. Right.

Even for the vu-meter must configure the various modifiers ?

Yes

I read that there are four configuration modes vu-meter ( I can not find examples )

I don't have the manual. Here is what I know.

While on PFL

Left side Channel A = parameter 22 channel 6
Left side Channel C = parameter 22 channel 8
Right side Channel B = parameter 23 channel 7
Right side Channel D = parameter 23 channel 9

I don't know the channel for master vu. I suspect is 8 while the switch is in master mode

The left side is parameter 1f
The right side is parameter 20

[tonip]

the channels that you say are fine otherwise would be led off. I was referring to a tutorial that I read to find info in which reference was made to four configuration modes LED

[tonip]

Is possible for master 1f and 20

[FigDJ]

the channels that you say are fine otherwise would be led off. I was referring to a tutorial that I read to find info in which reference was made to four configuration modes LED

here is what I got

MIDI map data is what I found in the internet.

The Mod3 file has the master vu meter mapped but I and guessing on this one.

mixer one(Dj-Tech)Mod3.mappings

MIDI map Data.zip

[tonip]

vu-meter , I was doing the tests, with different channels , I tried ch =6 and ch = 8 but only works with ch = 8 and the switch to A.
Switch B and D ok .
the map of the player channels are reversed A/C=6/8 e B/D=5/7