djsamrties wrote:ok,
everything is all right,
its just me who dont understand the new version but it works very fine thanks a lot !
No worries, I know it may take a little bit to get used to it but once you got the concept it is a good way to work it for this controller.
djsamrties wrote:so i can finish to notice everything and can send to you the excel file :..
Comment from the xlx file and responses.
Switch Sampler PlayerCFeedbackdont work
ResponseThis is now fixed
StartBrakeTime Player 1,2,3,and 4Feedbacksorry but i dont know what it is so i cant test it
ResponseIn the general setting there is a setting for start and brake time.
When you press play/pause or course the track starts or pauses
You can adjust the amount of time a tracks takes to start and pause.
1. Load a track in Player 1
2. Notice the reponsiveness of the play pause
3. Open setting in the general section and notice the radial knobs on the bottom.
4. Use the control to vary the start and brake time.
5. Now use the play pause in your deck and see how it is different now.
Display Zoom Player 1,2,3, and 4Feedbackthe zoom works but it only can jump to very close zoom to very high zoom. Its not possible to choose a value between BIG ZOOM and BIG DEZOOM
ResponseThanks for finding that one. I had mapped it work the DDJ-FX which has an endless encoder in that position and address while the DDJ-SR has a direct fader knob. It was wrong in the Audio and Video files. It should work now but I am unable to do a general test from my current location. Please test.
Enable Titler ImageFeedbacksorry but i dont know what it is so i cant test it. Maybe only with video ?
ResponseThis command is not present in the Audio file so nothing to test. I just forgot to say in the notes that this command is for the video file only. I added the proper comment in the spreadsheet to reflect that this is a video only command.
PAD PLUS / ONFeedbackbutton allow to switch hot cue to hot cue roll, roll to trans, slicer to combo fx and sampler to sampler roll. Actually it works, but the combo fx doesnt work. And i remember that in older version, it worked
ResponseFunny because I never mapped anything to this button which seems to be a hardware function. All the previous versions are available online and they numbered. So if you remember which version you are referring to that worked, let me know and I will take a look.
TICKS / TURN VALUEFeedbackstill 2400 and i continue to think that 500 is a better value
ResponseThis is a user preference that can be changed by using Cross MIDI learn to change the value or adjusting the sensitivity by following the instructions on the DDJ-SR manual.
However, word of caution about changing the value. Best practice in this case is to leave it at 2400 and change the sensitivity from the controller.
Example: The current value of 2400 allows for maximum sensitivity up to 2400 which allows for the hardware to operate from 1 to the 2400 limit. If the number was changed to 1/2 of that to 1200. Then your controller adjustment is only effective from 1 to 1200. The maximum sensitivity of the jogwheel will be 1200. By leaving the value at 2400 your allowing the hardware to be adjusted to the from minimum to the maximum value without re-writting the controlling map.
Loop Halve and Loop DoubleFeedbackyes, but only when loop are playing. This button do nothing when loop are not playing. I think, that It have to do the same function
even if the loop is not playing.
ResponseI will make a customized version for you on this buttons.
To be clear, i have no problem in modifying the mapping to make this happen but it should only be done after the Audio version is finalized.
Do you like the different navigation in the Audio file?
For MikeDDJSR_31_AV.zip
I did some cleanup work on the file and other than the Zoom function fixed everything else is the same in the Video version. Unless there are aditional issues I consider the video version now finalized. Please let me know.
You do not have the required permissions to view the files attached to this post.