by ddjj on 01 Jul 2013, 22:20
Good day all!
I just purchased the Quneo controller recently...I am in no way a master of programming this! I have completed a few simple commands on the pads...I need help on the LED portion..for instance:
Get the play pad to flash to the beat!
If I can get someone to help maybe I can figure out the rest!
(Please don't give me the response "Read the manual and figure it out"... I have done my due diligence and am stuck at this point!
Thx DDJJ
Dell Inspiron with I7 processor Windows 8.1 8 GB Ram, 1 TB Hard Drive Audio 2 DJ Soundcard Allen and Heath 62 Mixer 1 Quneo Controller Internal Intel graphics card GT 630m Nvidia Graphics Card
-
ddjj
-
- Posts: 175
- Joined: 23 Sep 2003, 08:44
- Location: phoenix, arizona USA
by gullum on 01 Jul 2013, 23:00
I do not have the Quneo so don't know what MIDI notes it sends. put to get the play button to flash you meed the set the output to - Code: Select all
fam(Player)[0x1].BeatFlash
Here is an exsample from my mapping for DDJ SX - Code: Select all
<mapping> <control alias="fam(Player)[0x1].BeatFlash" value="true"/> <MIDI type="Note" parameter="0xb" channel="0x1" value="127"/> </mapping> <mapping> <control alias="fam(Player)[0x1].BeatFlash" value="false"/> <MIDI type="Note" parameter="0xb" channel="0x1" value="0"/> </mapping>
hope this is of some help
-
gullum
-
- Posts: 222
- Joined: 10 Dec 2012, 18:25
- Location: Klaksvik, Faroe Islands
-
by ddjj on 02 Jul 2013, 00:09
Thx Gullum:
So I just copy and paste this into the output mappings? Quneo has an editor as well....do I do anything in that?
Thx DDJJ
Dell Inspiron with I7 processor Windows 8.1 8 GB Ram, 1 TB Hard Drive Audio 2 DJ Soundcard Allen and Heath 62 Mixer 1 Quneo Controller Internal Intel graphics card GT 630m Nvidia Graphics Card
-
ddjj
-
- Posts: 175
- Joined: 23 Sep 2003, 08:44
- Location: phoenix, arizona USA
by ddjj on 02 Jul 2013, 04:18
Ok, I'm kinda following, I'll see what I can come up with!
Thx DDJJ
Dell Inspiron with I7 processor Windows 8.1 8 GB Ram, 1 TB Hard Drive Audio 2 DJ Soundcard Allen and Heath 62 Mixer 1 Quneo Controller Internal Intel graphics card GT 630m Nvidia Graphics Card
-
ddjj
-
- Posts: 175
- Joined: 23 Sep 2003, 08:44
- Location: phoenix, arizona USA
by djphaidon on 02 Jul 2013, 07:29
ddjj,
I don't use the beatflash output, but what you have to do is use Cross to send back the CC of the button you want on the QuNeo according to the QuNeo manual. In the LED feedback section near the end of the book, it describes how to get LED's lit by sending inputs to it, and which modes do what. The QuNeo has 3 different requirements for LED feedback depending on what setting the pads are in, Grid or drum, and if you want to do other programming with a 1 note per corner setting. Each is on a different channel.
Also, Very important If you have the quneo set to "Local LED Control", no matter how you program Cross, you will not get the feedback you want. You have to go into the QuNeo editor, select the buttons you want to have feedback on, and uncheck the "Local LED Control" buttons. By default, they are on for quite a few of the preset, which might be why you are banging your head against the wall.
Hope it helps.
MixVibes Cross 2.6.0A&H Xone:DB4 / A&H Xone:K2 / QuNeo / iPad Lemur 15' MacBook Pro / 16Gb RAM Retired: Jazzmutant Lemur / Korg padKontrol / Korg Zero 4 / VCI 100 / APC40 / NI S4 / Traktor
-
djphaidon
-
- Posts: 423
- Joined: 21 Aug 2012, 06:17
- Location: Reno, NV
by ddjj on 02 Jul 2013, 08:47
Thanks DJ Phaidon:
yep, a whole lot of banging going on! What do you use to make the LEDs flash to the beat of the music then? I'll use your suggestions and let you know how it works out!
Thanks DDJJ
Dell Inspiron with I7 processor Windows 8.1 8 GB Ram, 1 TB Hard Drive Audio 2 DJ Soundcard Allen and Heath 62 Mixer 1 Quneo Controller Internal Intel graphics card GT 630m Nvidia Graphics Card
-
ddjj
-
- Posts: 175
- Joined: 23 Sep 2003, 08:44
- Location: phoenix, arizona USA
by FigDJ on 02 Jul 2013, 12:48
MIDI Conversion Table2.xlsx ddjj wrote:Thanks DJ Phaidon:
yep, a whole lot of banging going on! What do you use to make the LEDs flash to the beat of the music then? I'll use your suggestions and let you know how it works out!
Thanks DDJJ
DJ Phaidon is right on the money specially about making sure Quneo is in remote LED mode. I created a conversion table to guide me when I am mapping output for Quneo. In the file you will see 3 values listed as N Q and H N is the actual note value on the table Q is the Quneo value for a particular LED H is the equivalent hexadecimal value that you use in Cross to tell the Quneo to activate the LED. Some values are color coded, those are the colors that Quneo LEDs will turn on. Keep in mind that Quneo has 8 LEDs per pad 4 red and 4 Green. All LED on at 127 intensity will give you orange. A green LED at 127 and a red LED at 15 in the same location will make it light up yellow. Many combinations are possible. I use the combinations make make Quneo light up in tune with Cross color scheme with the decks and cue points.
You do not have the required permissions to view the files attached to this post.
-
FigDJ
-
- Posts: 1355
- Joined: 22 Apr 2012, 17:03
- Location: Odenton, MD
by discopex on 02 Jul 2013, 21:10
Will post my Quneo mapping later today or tomorrow. I just have to make the instructions which is the boring part really. My mapping is for 2 decks (+2 decks with less controll, for example simple loops) with many functions, fx, collection browsing, loading, loops, beatgrid, slip mode etc. For external mixer.
Thinkpad X240, 8 Gb / 512Gb SSD running Cross 3.4.3 64-bit Allen & Heath K2, Pioneer DJM-450
-
discopex
-
- Posts: 506
- Joined: 02 May 2007, 09:45
-
Return to Mapping Midi
Users browsing this forum: No registered users and 14 guests
|
|
|