light dj-tech dragon two

[FigDJ]

Dragon(DJ Tech)TV4.mappings

1)pitch fader is reversed (+/-)(-/+)

I think is fixed now, please try it.

2)jog weel steady light and does not rotate.

Output not supported by Cross

3)"Select" knob = not work.

Made some changes, see if it works now.

4)"sampler" button = not work.

Used to Switch between sampler 1 and sampler 2 see notes

5)"effect" button = not work.

Used to show or hide effects band

6)"browser" button = work but not light.

I think this one is fix now, please try it.

7)"record" button = work but not light.

This one is fixed.

8)rotary encoders near the channel meters = you push and enable / disable loop, but turning the knob does not change the length of the loop.

Need more information on this one. Please take a close look.
Is not moving at all?
Also LEDs not yet mapped until I get the knob working.

I must to recheck sampler / effects because maybe I did not understand what should happen by pressing the button ...
with "virtual DJ " = you push sampler and effects buttons and screen opens ...
with "virtual DJ" = If you push "P1-FX on" the light is "ON" for 2 encoders
with "virtual DJ" = the knobs of the filters when they are activated light is "flashing"

Dragon 2 map notes.txt

Cross works a little different please see map notes.

[FigDJ]

On that last file version I may have reversed the values for proper filter operation. So please test and let me know.

Also the deck selector switches are not yet map because I think that the required channel change is hardware controlled. So please load tracks on player C and D and check if the transport controls work (play, sync...)

Last thing is check if the ring lights around the Hi, Mid, and Lo do anything when the player selectors are changed from A to C and B to D.

Make sure Cross and the controller are both in 4 deck mode.

Feedback needed to finalize the map.

[FigDJ]

Dragon 2 map notes.txt

Dragon(DJ Tech)TV5.mappings

New update, I was mistakenly using the parameter for the deck encoder in the commands for the select encoder.

I made some changes and updated the notes file

Please test TV5= Test version 5

[ROZE61]

Hi, feedback version 4
this map is much more than I hoped ... but if you want to perfect to give everyone the right map, okay, let's move on ... I do not want take advantage of your kindness...
1) pitch = is ok
2) select = not work
3) sampler = is ok
4) effect = work but no light
5) record = is ok
6) browser = no light
7) rotary encoders near the channel meters = loop enable/disable is ok, but no light and not change the loop lenght
8) filter lights = in the position 0 light no work but when operating light is flashing (ok)
----------
songs uploaded to player C and D:
response equal to A and B players, fully functional ...
Player C and D ring work lights changing color.
----------
Now I try latest version, you are too fast for me ...

[daniel clark]

Hi, feedback version 4
this map is much more than I hoped ...
Now I try latest version, you are too fast for me ...

MIDI MONSTER
AT WORK

[FigDJ]

Hi, feedback version 4
this map is much more than I hoped ...
but if you want to perfect to give everyone the right map,
okay, let's move on ... I do not want take advantage of your kindness...

Thank you for the kind words. It is nice to be appreciated.
I know it is a lot of back and forward but that is because I don't
have the controller to be able to test things so I appreciate your time doing performing tests and your feedback.

1) pitch = is ok
3) sampler = is ok
5) record = is ok
7) rotary encoders near the channel meters = loop enable/disable is ok,....

Great

2) select = not work
4) effect = work but no light
6) browser = no light
7) ......but no light and not change the loop lenght
8) filter lights = in the position 0 light no work but when operating light is flashing (ok)

2) I think I fixed the problem on TV5 file
4) I think I fixed the problem on the coming TV6 file.
I am looking for both ring LEDs to turn on when the effect is active.
The effect button on the right is for changing display only and it should light up only when the effects band is displayed in Cross.
6) I think I fixed the problem on the coming TV6 file
I am looking for the button to light up only when is pressed.
7) I think I fixed the problem on TV5 file.
LEDs are not yet mapped until the knob is working correctly.
8. Please clarify
In the center position the LED ring is off
Out of center position the LED ring blinks
Is that the correct statement?

Do you want the Filter LED rings to do as follows?
In the center position the LED ring is on
Out of center position the LED ring blinks

songs uploaded to player C and D:
response equal to A and B players, fully functional ...

So that means that all deck functions (with the exception of the loop knob problem) on Players A,B,C and D work.

Does using the Deck selection switches correctly switches A to C and B to D?
I understand by your statement that is a Yes. If no please correct me and clarify.

Player C and D ring work lights changing color.

Do they change back and forward as you switch decks correctly? What are the colors for each deck.

Now I try latest version, you are too fast for me ...

Dragon(DJ Tech)TV6.mappings

You might want to skip TV5 and go straight to TV6 because some fixes went on to TV5 and those fixes plus other ones are on TV6.

[ROZE61]

Hi FigDj

filter lights:
center position ring off (correct)
Out of center position the LED ring blinks (correct)
-------------------------
filter led rings:
in the center position the LED ring is on (correct)
Out of center position the LED ring blinks (correct)
this is same at virtual DJ
-------------------------
Does using the Deck selection switches correctly switches A to C and B to D?
yes,correctly > switches a/c and b/d
-------------------------
switch decks correctly? yes
What are the colors for each deck? blue for a/c and red for b/d (correct)
-------------------------
sorry I forgot to say to you:
...with "virtual DJ" = If you push "P1-FX on" the light is "ON" for 2 encoders...
Now if you press the left encoder also lights on the right...
-------------------------
Now I try the version 6
Thanks

[FigDJ]

I am sorry but i am a little confused by your stement below

filter lights:
center position ring off (correct)
Out of center position the LED ring blinks (correct)
-------------------------
filter led rings:
in the center position the LED ring is on (correct)
Out of center position the LED ring blinks (correct)
this is same at virtual DJ
-------------------------

The top and bottom present 2 diferent states for center position, how can both be correct? Or it is that there is a difference because the top is lights? and the bottom LED ring?

Does using the Deck selection switches correctly switches A to C and B to D?
yes,correctly > switches a/c and b/d
-------------------------
switch decks correctly? yes
What are the colors for each deck? blue for a/c and red for b/d (correct)

that is great.

-------------------------
sorry I forgot to say to you:
...with "virtual DJ" = If you push "P1-FX on" the light is "ON" for 2 encoders...
Now if you press the left encoder also lights on the right...
-------------------------)

The left encoder push is what activates the FX unit. I ntended for both encoders to turn on to show that Amount and Depth knobs are active. (Check bi-dimentional effects preference is selected in Cross settings)

For the next text is very important to check for the select knob and the loop encoders next to the meter LEDs. if those fail then I have some task (mappings) that I would like you to do using MIDI learn in order to gather information about the controls.

[ROZE61]

sorry I have not explained well ...
you asked:
8. Please clarify
In the center position the LED ring is off
Out of center position the LED ring blinks
Is that the correct statement? - YES for all
----------------------------
you asked:
Do you want the Filter LED rings to do as follows?
In the center position the LED ring is on
Out of center position the LED ring blinks
yes, it if you can (same virtual DJ)
----------------------------
----------------------------
left encoders
Version 4 - 2 knobs simultaneously light is perfect
Version 6 - works but no light
-----------------------------
shift no light
-----------------------------
browser light ok
-----------------------------
effect light ok
-----------------------------
select -
not one by one but jumps blocks ...
-----------------------------

[ROZE61]

Hi, I did not see the problem ...
encoders placed over S4 button:
strangely in this version (v6) up and down the songs but always jumping groups (no one by one)...
contrary to encoder placed over S2 button which shall function regularly (but not light)