Page 1 of 1

Problem mapping lights (dj-tech dragon two)

PostPosted: 18 Nov 2015, 13:53
by ROZE61
Hi, I have problem mapping for my DJ-TECH dragon two. :(
1) the lights not operate.
The lights work exclusively in the eq zone mixer (bass-mid-treble) + scroll traces knob + light jog (but do not turn) + LED Vmeter master (not the fader left and right). there is a way to make them work all?
2) When using Cross in timecode with my turntables and dragon2 there are problems at the faders.
When I get up they have an uncertainty of volume (lowers and then resumes). This happens at the print line before max level volume.
I hope for some help, please if you can speak simple, my mind is 95% analog and 5% digital :lol: ... Thanks

Re: Light mapping (dj-tech dragon two)

PostPosted: 18 Nov 2015, 14:30
by RoJeC
Likely FigDJ can help you out, at least some further.

What you can do as preparation is to upload your MIDI mapping file.

It would also be (very) helpful if you can upload or link to the MIDI commands table of the device. This table shows which commands the device needs/has for each control.

Re: Light mapping (dj-tech dragon two)

PostPosted: 19 Nov 2015, 15:22
by ROZE61
Dragon Two midi map 3.pdf
(636.01 KiB) Downloaded 1486 times
Dragon Two midi map 2.pdf
(680.98 KiB) Downloaded 1474 times
Dragon Two midi map 1.pdf
(361.73 KiB) Downloaded 1461 times
Hi Ronald,
Thanks for your help!
I send my mapping and MIDI map dj-tech.
maximum of 3 attachments, I send two messages...
Thanks again and good music :)
Roby

Re: Light mapping (dj-tech dragon two)

PostPosted: 19 Nov 2015, 15:26
by ROZE61
Dragon(Dj Tech).mappings
(43.55 KiB) Downloaded 1605 times
Dragon Two midi map 4.pdf
(560.68 KiB) Downloaded 1475 times
Sending completed

Re: Problem mapping lights (dj-tech dragon two)

PostPosted: 14 Mar 2018, 04:17
by ZagaDj
Hi, I downloaded your MIDI mapping for my DJ Tech Dragon Two and it works good.
The only thing that I can't do is to activate the sound in the headphones: the Cues buttons lights of channels A and B are always with light on and when I push one of it to switch on the sound in headphones, the button lights intermittently and the sound does not come. Can you help me please ?
thanks a lot.

Re: Problem mapping lights (dj-tech dragon two)

PostPosted: 19 Mar 2018, 14:56
by FigDJ
ZagaDj wrote:Hi, I downloaded your MIDI mapping for my DJ Tech Dragon Two and it works good.
The only thing that I can't do is to activate the sound in the headphones: the Cues buttons lights of channels A and B are always with light on and when I push one of it to switch on the sound in headphones, the button lights intermittently and the sound does not come. Can you help me please ?
thanks a lot.


You might get better help with the other user in this thread who I worked with for weeks to map this controller remotely.
When I say remotely it means that I made a map, send it to him.
He would test it and tell me what worked and what didn't. We went back and forth like this for quite some time before it was finally done. However, when it comes to the audio routing, that is something that must be working correctly before any MIDI mapping could work correctly on audio related controls.
I don't have the controller and therefore can't help on that particular. Perhaps someone who downloaded the map and it is working OK with it can help you.
Unless of course a Mixvibes decides to provide some support.

Re: Problem mapping lights (dj-tech dragon two)

PostPosted: 24 Mar 2018, 16:15
by ZagaDj
Ok, thanks a lot.