Page 14 of 17

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 12:59
by djsamrties
i am working on an image that can be a support to quickly remember all the functions.
and i notice that i dont ask you what is ? :

- Audio Video Fx1 Switch : Select FX1 mode Audio, Video, Audio+ Video

- Bidimensionnal Fx On Off : Toggles bidimentional effect on/off for FX units 1 and 2

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 13:09
by FigDJ
djsamrties wrote:i am working on an image that can be a support to quickly remember all the functions.
and i notice that i dont ask you what is ? :

- Audio Video Fx1 Switch : Select FX1 mode Audio, Video, Audio+ Video

- Bidimensionnal Fx On Off : Toggles bidimentional effect on/off for FX units 1 and 2

Yes, while the Audio Video FX Switch does not apply if you are using audio only I thought it unnecessary to remove.
The enabling of bidimentional effect can only be done for both fx units at the same time. This is a Cross limitation.

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 13:25
by djsamrties
in the same way, i try to use the function to tap tempo and confirm with Word censored (guess you find it I love walking on it) + CUE. I can define the tempo with Word censored (guess you find it I love walking on it) + CUE but i cant confirm it. I dont know if i do this correctly so maybe Mike DJ can test this ?

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 14:37
by FigDJ
djsamrties wrote:in the same way, i try to use the function to tap tempo and confirm with Word censored (guess you find it I love walking on it) + CUE. I can define the tempo with Word censored (guess you find it I love walking on it) + CUE but i cant confirm it. I dont know if i do this correctly so maybe Mike DJ can test this ?


There a little delay built into Cross.
When you are using tap tempo, you keep tapping for the beats, once the indication of the beat is correct the switch on the GUI takes couple of seconds to be set for confirmation. Then you press again to confirm. Try it on the GUI using your mouse to get used to the timing then try it with the controller.

As you can see from the Quote above, I did not get the meaning of your post completely.

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 14:38
by djsamrties
here is another few little notice...

in the excel file, in mixer sheet, i think that you have forgoten the line about HEADPHONE MIX.

With the button to switch between ch 1/2 or MASTER level, it only work with 1/2 channel. And i think that in an ald version of your map, it was possible to switch and see MASTER level with it.

in the excel file, in mixer sheet, i think that you have forgoten to write FADER CHANNEL just above CUE. and the description for use FADER CHANNEL + SHIFT isnt the good description.

i think that the SHIFT + SLIP doesnt work. it normaly have to load and read the same track that the master isnt it ? if its that, it doesnt work for me.

and to finish, here is the reminder image that i have done to try to use each function. Hope that you will like it :)

ddj sr reminder djsmarties.jpg


and here is an empty version if MIKE DJ want to do the same with video version :)

ddj sr reminder empty.jpg

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 15:15
by FigDJ
djsamrties wrote:here is another few little notice...

in the excel file, in mixer sheet, i think that you have forgoten the line about HEADPHONE MIX.


I did not forget. I left that out on purpose because it is a harware button. The settings for that are describe on page 1 of the DDJ-SX pdf file provided by Mixvibes. This file describes the set up and proper position for the GUI and controller buttons which I am pretty sure I mentioned as a caveat for the mapping couple of times.


djsamrties wrote:With the button to switch between ch 1/2 or MASTER level, it only work with 1/2 channel. And i think that in an ald version of your map, it was possible to switch and see MASTER level with it.


I just looked again at the MIDI tables for the controller to verify. Please make sure you are set up correctly. On the DDJ family of controllers Channels 1,2,3,4 control the level meter and they are mapped accordingly. The master level meter is hardware controlled.

djsamrties wrote:in the excel file, in mixer sheet, i think that you have forgoten to write FADER CHANNEL just above CUE. and the description for use FADER CHANNEL + SHIFT isnt the good description.


I didn't think it was necesary to explain the channel fader. For a matter of completness yes it should be there.

Just to make it clear to anyone watching the tread. The xcel file that djsamrties is referring to is just a descriptive file that does not affect the operation of the controller.

djsamrties wrote:i think that the SHIFT + SLIP doesnt work. it normaly have to load and read the same track that the master isnt it ? if its that, it doesnt work for me.


Make sure that you are not usinf version 3.0 of Cross
In 2.6 it worked.
in 3.0 It was broken
In 3.1 it is fixed.

This was one of the bugs that i called out during testing.

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 17:25
by djsamrties
djsamrties wrote:Make sure that you are not usinf version 3.0 of Cross


i use 3.0.1 version and it doesnt work.
But i remember to use this function during all the tests that we did...

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 17:40
by FigDJ
djsamrties wrote:
djsamrties wrote:Make sure that you are not usinf version 3.0 of Cross


i use 3.0.1 version and it doesnt work.
But i remember to use this function during all the tests that we did...

You mean 3.1 right?

Re: MAPPING FOR DDJ SR

PostPosted: 06 Jun 2014, 18:03
by FigDJ
djsamrties

I forgot to explain the Shift+ channel fader.
This is also called fader start.

load a track pause it either at a cue poit or any other point.

turn thr channel fader down to minimum.

If you Press and hold shift + move the channel fader up you will see the track start just abot the mid point of the fader travel.

Re: MAPPING FOR DDJ SR

PostPosted: 10 Jun 2014, 23:00
by djsamrties
i have buy Cross DJ in april,
i ask for version 3.1.
I have the answer that 3.0.1 is the 3.1 version but its not very clear.
In fact, when i look in "Cross DJ" and in the "about corss DJ" i can see 3.0.1 in the right corner.
Dont you have the same version ?