MIDI commands for...(Missing?)

  
Forum rules
Click here to join MIxvibes on DISCORD https://discord.gg/gMdQJ2cJqa

MIDI commands for...(Missing?)

Postby ddjj on 02 Oct 2013, 01:01

Greetings:

I'm looking for the MIDI commands for :

a. reset zoom
b. pitch reset
c. clear the data (x in the spotlight)

also if there appears to be no output command to light up LEDS in my quneo...is there a way to do this in Cross? such as smart seek forward and smart seek length? and even the above?

Thanks
DDJJ
Dell Inspiron with I7 processor
Windows 8.1
8 GB Ram, 1 TB Hard Drive
Audio 2 DJ Soundcard
Allen and Heath 62 Mixer 1
Quneo Controller
Internal Intel graphics card
GT 630m Nvidia Graphics Card
ddjj
 
Posts: 175
Joined: 23 Sep 2003, 08:44
Location: phoenix, arizona USA


Re: MIDI commands for...(Missing?)

Postby P_Jean on 02 Oct 2013, 11:30

ddjj wrote:Greetings:

I'm looking for the MIDI commands for :

a. reset zoom
b. pitch reset
c. clear the data (x in the spotlight)

also if there appears to be no output command to light up LEDS in my quneo...is there a way to do this in Cross? such as smart seek forward and smart seek length? and even the above?

Thanks
DDJJ


a . reset zoom --> create a Reg(registerlogic) with the same Value .
b . Pitch reset --> command --> PitchZeroOuput(logic)
c . clear the data ---> create a Reg(registerlogic) with the same value.
User avatar
P_Jean
 
Posts: 2436
Joined: 09 Dec 2009, 17:24


Re: MIDI commands for...(Missing?)

Postby FigDJ on 02 Oct 2013, 14:28

ddjj wrote:Greetings:

also if there appears to be no output command to light up LEDS in my quneo...is there a way to do this in Cross? such as smart seek forward and smart seek length? and even the above?


Do a little search for the topics related to Quneo. I posted a zip file that contains a Microsoft Xcel file with a MIDI conversion table for the LED using Quneo.

It boils down to this:
With Quneo a C note is mapped to the decimal value 60, you must convert that value to a hexadecimal value. Then you can use the hexadecimal value in output commands from Cross to Quneo to light up or turn off LEDs.

The last page of the Quneo manual has a table with the conversion from MIDI notes to decimal values. Somewhere in the middle of the Quneo manual (after the presets section) there are graphics that shw the Quneo pads and controls with the required MIDI notes to control the LEDs.

Select the pad or control you want to light up and note the assigned MIDI note. (Quneo manual)

Go to the end of the Quneo manual to look up the decimal value.

Go to the file I posted to look up the corresponding hexadecimal value for Cross output commands.

You should take a careful look at the file that I posted as it has all the MIDI notes, decimal values, hexadecimal values, and graphical representations of Quneo LEDs in drum and grid modes.

I am working from my iPad right know so i can't post the links or upload the manuals but you should be able to get everything you need from the KMI website for Quneo and this forum for the conversion files. (Note I own 2 Quneo and light them up like a show with Cross)
Image
FigDJ
 
Posts: 1355
Joined: 22 Apr 2012, 17:03
Location: Odenton, MD


Re: MIDI commands for...(Missing?)

Postby sylMV on 02 Oct 2013, 15:20

ddjj wrote:Greetings:

I'm looking for the MIDI commands for :

a. reset zoom
b. pitch reset
c. clear the data (x in the spotlight)


All the input commands are listed in the MIDI mapping interface, did you check it?

a. Use "Display Zoom" in "Direct Normal Button" with value "50".
b. Use "Pitch Value" mapped in "Direct Value" with value "0.5".
c. To clear the spotlight, you need give it the focus and press ESC on your keyboard.
SylMV

Image
User avatar
sylMV
 
Posts: 3098
Joined: 04 Jan 2007, 10:38


Re: MIDI commands for...(Missing?)

Postby ddjj on 03 Oct 2013, 19:55

Gentlemen:

I used the suggestions from SylMv to get this going!
Wish I Could avoid using the esc command for C: though, was hoping for an all MIDI command, oh well!

To FigDJ:

I have your xls sheet from prior and I understand the LEDs and their locations, but I'm looking for the language in the file to turn on and off leds when there is no such in Cross: IE
output mapping
display zoom at 07e on (or off)
outmapping....does this make sense?

and finally, trying to find "registers" in the manual, to read up on and can't find now...

Thanks
DDJJ
Dell Inspiron with I7 processor
Windows 8.1
8 GB Ram, 1 TB Hard Drive
Audio 2 DJ Soundcard
Allen and Heath 62 Mixer 1
Quneo Controller
Internal Intel graphics card
GT 630m Nvidia Graphics Card
ddjj
 
Posts: 175
Joined: 23 Sep 2003, 08:44
Location: phoenix, arizona USA



Return to Mapping Midi




Who is online

Users browsing this forum: No registered users and 80 guests

Board index

 
 
   
 
© 2014 Mixvibes