MIXVIBES Dj Community old forum

I stop trying run stabil DVS 7 on my netbook so i bought new gaming laptop but with windows 7 when i first install DVS on this system (patch and v3 driver) it ran correct. But when i start DVS again second time in club so that was terrible ... DVS has not signal from vinyl and didnt calibrate both turntables with same problem.. oh f--k. when try bypass mode so i heard beep from vinyls. New installation of DVS with cleaning registers dont help, full reinstallation of win7 dont help, change type of drivers dont help... looks lide windows7 blocking DVS signal or i dont know.. please help im desperate

It was ok at home, but not at club...
and back home how it is ? still dead ?

dont matter on location. At home at club everwhere dead no signal. i have lowest level security of program its only think what i found at windows 7 what can blocade program but without success.

publish a config report from DVS menu

UncleVibes wrote:publish a config report from DVS menu

here is it:

Config 2010/11/04 21:41

OS= build=7600 processor=PROCESSOR_IDENTIFIER=Intel64 Family 6 Model 37 Stepping 2, GenuineIntel
MixVibes DVS version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=No Equalization bypass=No
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=MIXVIBES U46MK2 ASIO AsioVersion=0 DriverVersion=2
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=6
Managment Type ASIO
1-MIXVIBES U46 1/2:L 2-MIXVIBES U46 1/2:R
3-MIXVIBES U46 3/4:L 4-MIXVIBES U46 3/4:R

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:MIXVIBES U46 1/2:L-MIXVIBES U46 1/2:R
Mode=absolute
Riaa=Yes Preamp Left=0 db Preamp Right=0 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:MIXVIBES U46 3/4:L-MIXVIBES U46 3/4:R
Mode=absolute
Riaa=Yes Preamp Left=0 db Preamp Right=0 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000

I have the same problem here.
The last time i used it was at a club, the other day at home there was no signal, "check needle" it said.
I reinstalled the v3 driver, no succes, uninstalled Mixvibes, cleaned register and than reinstalled Mixvibes with all its updates, still no signal.
When i connect my turntables directly to the mixert i can here the DVS signal loud and clear, i can hear it also when the turntables are connected to the soundcard (u46) but still not in use, so the problem is not situated in the turntable.

Both of you are having the same issue.

if you play a sound from the virtual decks (vinyl off on the gui), does it outputs on the U46 as it should ?

Support@MixVibes wrote:Both of you are having the same issue.

if you play a sound from the virtual decks (vinyl off on the gui), does it outputs on the U46 as it should ?

when i have vinyll off , i can not play decks from DVS. When i press play nothing happened. In bypass mode i hear beep sound from A and B turntable right same result with normal vinyl. Same in windows i can play sound over U46 channel 1 so drivers works good. May be i dont understand what are you exactly asking for.. my english is terrible sorry .

Hollender wrote:I have the same problem here.
The last time i used it was at a club, the other day at home there was no signal, "check needle" it said.
I reinstalled the v3 driver, no succes, uninstalled Mixvibes, cleaned register and than reinstalled Mixvibes with all its updates, still no signal.
When i connect my turntables directly to the mixert i can here the DVS signal loud and clear, i can hear it also when the turntables are connected to the soundcard (u46) but still not in use, so the problem is not situated in the turntable.

Accept my deapest condolences

There is something wrong in your setup as you both have a proved and reliable software where we aren't at all in an experimental alpha stage.
As I know DVS works perfectly so I think you miss something.
You have no sound coming from mp3 decks and mixvibes. With the config report I have seen this is incredible if the setup is well done. But in vinyl mode there isn no setup done as both deck are at Odb that's true it can't work like that. The U46MK2 is a good sound card and your computer see it in Asio. I never thought your situation in years except when the plugs aren't in their good positions. So check your wiring to your mixer. The 2 outputs of your U46MK2 must be line one & 2 on your mixer. The output of your mixer must go to your amplifier & loudspeakers. The inputs of the U46MK2 must go to the outputs of your turntables. You don't have a driver problem as they are well recognized.
With the elements I got from you on this forum it's all I can say now to help you.