MIXVIBES Dj Community old forum

The last 2 saturdays i got 2 "Mixvibes is Not Responding". Both times this happened when loading a track.
I hope anyone have an idea to check for a solution.
- No Antivirus installed
- All internet and network services disabled

Also this is my config file...

Config 2010/04/17 22:16

OS=Microsoft Windows XP Service Pack 3 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 14 Stepping 8, GenuineIntel
MixVibes Producer version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=No Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=8
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=No AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=182
Loop in bar boundaries=No Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=Audio 4 DJ AsioVersion=0 DriverVersion=512
Latency=6 Driver sampling=48000 Nb Input=4 Nb Output=4
Managment Type ASIO
1- 2-
3- 4-

Vinyl Configuration
--------------------
Vinyl 1 not connected
Vinyl 2 not connected
Vinyl 3 not connected
Vinyl 4 not connected

Thanks a lot
Stelios, Greece

If for any reasons the firewire or usb stops then Mixvibes got to close. This is related to a hardware problem of firewire/usb or a problem with your sound card hardware or driver.

When loading ?
Do you use an external hard drive ?

does it happen with the same track each time ? i had this happen once and it turned out to be a corrupt .vpk(mediabase peak file) file causing a crash on load. i deleted the song from the mediabase and rescanned/analyzed the file. hope it helps

-No i don't use an external disc drive
-No it didn't happened with the same track

i recently updated my audio card drivers but it did happened with the previous version of drivers.

If it was my sound card's problem, shouldn't this happened with an other DJ software?

Thanks a lot!!!
Stelios, Greece

sfronti wrote:If it was my sound card's problem, shouldn't this happened with an other DJ software?

Yes, this should happen with any scratch software because of a bad timecode or anything else.

Greetings,

Steve

So yesterday I put MV in playlist mode and let it run with an Audio8 and nothing wrong.
I even disconnect the card while playing : nothing wrong, just paused the software.
As soon as I have reconnected the soundcard, it continue...

I'll try some more tests today.

Thanks a lot for all your answers. I am still testing Mixvibes with Audio 4 and on friday i am waiting an other card for testing.

Thanks a lot!!!
Stelios, Greece

I got the same results with a new sound card. Again, after loading a track MV 7.218 showed me "Not Responding".

here is my config file

Config 2010/05/01 23:18

OS=Microsoft Windows XP Service Pack 3 build=2600 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 14 Stepping 8, GenuineIntel
MixVibes Producer version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=No Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=8
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=No AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=182
Loop in bar boundaries=No Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=3 Nb Mixer=0
Managment Type ASIO
Device=Phase 26 USB ASIO AsioVersion=0 DriverVersion=34082560
Latency=6 Driver sampling=44100 Nb Input=2 Nb Output=6
Managment Type ASIO
1-OUT 0 - PHASE 26 USB(ASI 2-OUT 1 - PHASE 26 USB(ASI
3-OUT 2 - PHASE 26 USB(ASI 4-OUT 3 - PHASE 26 USB(ASI
5-OUT 4 - PHASE 26 USB(ASI 6-OUT 5 - PHASE 26 USB(ASI

Vinyl Configuration
--------------------
Vinyl 1 not connected
Vinyl 2 not connected
Vinyl 3 not connected
Vinyl 4 not connected

I hope someone has an idea what might 'caused the problem
Thanks a lot
Stelios, Greece

The same result with the Terratec ?
I don't know where is the issue because I nver had this one before.

Try reset.exe in the Mixvibes folder.