Page 1 of 1
My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
07 Mar 2010, 08:51by aznjesus44
Hello, im about positive that i have connected everything right but i still get a message saying "no input signal on the left connection. please check the connections." what am i doing wrong!!! im only setting up the right turntable so why would it even be saying anything about my left connection when im clearly trying to calibrate the right turntable. im confused!
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
07 Mar 2010, 09:07by phadedvision
Hi azn,
Double check to make sure your needle on the left is in properly and isn't dirty.
Hope this helps,
Phaded
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
07 Mar 2010, 12:27by Blackbrook
aznjesus44 wrote:Hello, im about positive that i have connected everything right but i still get a message saying "no input signal on the left connection. please check the connections." what am i doing wrong!!! im only setting up the right turntable so why would it even be saying anything about my left connection when im clearly trying to calibrate the right turntable. im confused!
Think of the pitch setting to zero!
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
10 Mar 2010, 06:12by aznjesus44
Is it possible one side of my rca is not giving any input? ahhhhh
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
10 Mar 2010, 09:33by UncleVibes
timecode use both left & right channel. If one channel is dead then any time code control is impossible.
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
10 Mar 2010, 10:41by sylMV
The error message you get really means the signal is "unbalanced", the signal power on the left channel being far lower (almost silence if not) than on the right one.
You really need to check your "connections" and ensure neither the TT output, nor the RCA cables, nor the u46 input are defective.
Cheers,
EDIT: The "left connection" is not the left TT but the left channel of the stereo TT connection (the white connector) !!!
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
11 Mar 2010, 03:32by aznjesus44
Yes, my rca are probably jacked up so once i solder some new ones on, then i will tell yall if it fixed the problem
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
11 Mar 2010, 21:19by hemskoc
Good luck with your mission bro!.... the thing with T1200s (im assuming this is what you have as your problem is common, but this applies to ALL hardwired rca TT's) is that because you cant remove the cables on factory models, after time they stuff up if you plug them in and out of mixers, ect...
My soloution was to hardwire some 'Male' rca inputs onto the back of the 1200, then you can plug and unplug replacement cables, and not revisit this situation. Easier to just get another cable, then have to open the thing up over and over (after the second time, it happened at a gig, i was over it)!!
Works a treat for my decks
Cheers
Just incase you didnt see this post on your other similar thread
Cheers
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
15 Mar 2010, 03:27by aznjesus44
dang, it wasnt the rca.... now im thinking it is the wiring in the tone arm! i checked the rca, cartdridge, styli, and now i .... need help! any ideas!
Re: My technics arent connecting to my u46mk2!! mixvibes Cross!
Posted:
15 Mar 2010, 03:31by phadedvision
aznjesus44 wrote:dang, it wasnt the rca.... now im thinking it is the wiring in the tone arm! i checked the rca, cartdridge, styli, and now i .... need help! any ideas!
Is there a shop near your area you can take it in to have it checked out?