MIXVIBES Dj Community old forum

when I connect my 2 cd players on the maya 44 sound card and the soundcard to my mixer, and i plug the soundcard in my computer and I start up DVS,mij right cd player send a signal because i see the lights burning on the soundcard , but DVS do not recognize the signal, and does not send a signal back to my mixer. I have used DVS several times and it works good, but now this problem appears.

Hi Wannes, could you send a config report (with both cds playing when you genrate it)

Config 2009/03/05 19:27

OS=Microsoft VISTA Service Pack 1 build=6001 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 15 Stepping 13, GenuineIntel
MixVibes DVS version=7.100 DLL langage=US version=7.100

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=No Equalization bypass=No
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=Maya44 USBAudio ASIO driver AsioVersion=0 DriverVersion=34083072
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=4
Managment Type ASIO
1-OUT 0 - MAYA44 USB 2-OUT 1 - MAYA44 USB
3-OUT 2 - MAYA44 USB 4-OUT 3 - MAYA44 USB

Vinyl Configuration
--------------------
Vinyl1 connected=CD
Audio=ASIO source=0:IN 0 - MAYA44 USB-IN 1 - MAYA44 USB
Mode=absolute
Riaa=No Preamp Left=0 db Preamp Right=0 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=90.476 Volume max left=0.664 Volume max right=0.659 Volume optimum=0.370
Speed Average(100ms)=1.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=CD
Audio=ASIO source=0:IN 0 - MAYA44 USB-IN 1 - MAYA44 USB
Mode=absolute
Riaa=No Preamp Left=0 db Preamp Right=0 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.000 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000

there is no timecode detection in your second input... check your connections, also switch your CD in the inputs to see if the problem is related to CD players or MAYA inputs.

seems like you might be using the same input for both channels. did you run the install wizard ?

Another idea would be to test the infamous ASIO4ALL driver with your MAYA. it gives great results. you'll find it a s freeware on the ASIO4ALL website.

tomorrow i'm going to buy new cables, but, i have already switched the cd players, but the problem remains.
i wll try the other solutions and let you know or it helps.