Unwanted noise

[Nathandj]

Can anyone help!!!!!!!!!

After loading MP3 and once the needle has been taken off the decks i get unwanted noise can only stop it by loading another track......

Any ideas PLEASE

onfig 2009/09/10 19:39

OS=Microsoft VISTA Service Pack 1 build=6001 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 23 Stepping 10, GenuineIntel
MixVibes DVS version=7.218 DLL langage=US version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=Yes Theme=3
TAG V1=Yes TAG V2=No

Mix Setting
--------------------
AutoCue=Yes AutoGain=No AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=No Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=Maya44 USBAudio ASIO driver AsioVersion=0 DriverVersion=34083072
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=4
Managment Type ASIO
1-OUT 0 - MAYA44 USB 2-OUT 1 - MAYA44 USB
3-OUT 2 - MAYA44 USB 4-OUT 3 - MAYA44 USB

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:IN 0 - MAYA44 USB-IN 1 - MAYA44 USB
Mode=absolute
Riaa=Yes Preamp Left=25 db Preamp Right=24 db Noise Filter=1 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=0 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.608 Volume max right=0.608 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:IN 2 - MAYA44 USB-IN 3 - MAYA44 USB
Mode=absolute
Riaa=Yes Preamp Left=24 db Preamp Right=23 db Noise Filter=1 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=0 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000

[Blackbrook]

Maybe you gained the input of your decks that the surrounded sounds recorded by your needle are recognized in mixvibes as slow timecode. I have this "problem" when I work without my audio interface and start mixvibes: the audio interface used then is my internal and input is the mic. So when I talk to someone else this is recorded by my mic in and mixvibes tracks are moving because it interprets my voice (nothing else than a sinus signal like the mixvibes timecode) as slow moving timecode. I think that this could be your problem, too. Maybe the needle OR a not muted Mic in. Check I out and report if this words could help you.

Greetings,

Steve