Mixvibes Dj Community old forum

Hi,

Somebody can help me to control Mixvibes vinyl timecode with DJM 900 NXS 2 ?
I don't understand why but when i connect by USB my NXS 2 (with latest firmware) to Cross (3.4.3) i cant control vinyl timecode with the NXS2 soundcard..
I have 2 turntables on the phono NXS channels 1 and 2.
I have the latest Pioneer drivers
I choosed the NXS2 soundcard in mixvibes Cross, check all input and output and no timecode signals.
Which NXS channel you choose for timecode ? Computer A, B, digital, line or phono ?

Thanks !

I retry, somebody use mixvibes Cross with the internal soundcard of the Pioneer DJM900 NX2 ?

thank you.

+1 please..

I tried with the last SIERRA OS and windows 7 same problem..
Mixvibes Cross recognize the soundcard but impossible to have timecode signal

I tried with SERATO too and work perfectly

no mixer 900 nxs ou 900 SRT tem que ficar na opção USB e só é possível utilizar time code vinil nos canais 1/2 e 7/8 que tem entrada Phono

Hey,

Thank you for the reply but that doesn't work...
i dont know why but its look like the Pioneer driver dont recognize phono timecode enter when i start mixvibes.

how do you configure your Pioneer panel driver ? CH 1 CONTROL TONE PHONO ? CH1 CONTROL TONE LINE ? POST CH1 FADER ??

The only way i found is to plug the turntable on the DJM line (and not phono) enter 1/2 and 3/4 and in the mixvibes panel redirect the enter in out number 5/6 & 7/8, but ni this case i have a 2 channel mixer and no 4 because the channel 1 & 2 of my mixer are the liner enter and the channel 3 & 4 are the out :/ ..

Totally crazy... I ask mixvibes support but no reply...

Hey,

Thank you for the reply but that doesn't work...
i dont know why but its look like the Pioneer driver dont recognize phono timecode enter when i start mixvibes.

how do you configure your Pioneer panel driver ? CH 1 CONTROL TONE PHONO ? CH1 CONTROL TONE LINE ? POST CH1 FADER ??

The only way i found is to plug the turntable on the DJM line (and not phono) enter 1/2 and 3/4 and in the mixvibes panel redirect the enter in out number 5/6 & 7/8, but ni this case i have a 2 channel mixer and no 4 because the channel 1 & 2 of my mixer are the liner enter and the channel 3 & 4 are the out :/ ..

Totally crazy... I ask mixvibes support but no reply...

I think the problem come from the Pioneer NXS 2 driver...
Henry Jay have you the DJM 900 NXS2 mixer ?

bozotaku wrote:I think the problem come from the Pioneer NXS 2 driver...
Henry Jay have you the DJM 900 NXS2 mixer ?

Não eu só tenho 900 nxs e SRT sei também que o Cross em 64 Bits não funciona com AsioDriver Pioneer

Uma pena que Mixvibes nos largou para focar em App de brinquedos

No I only have 900 nxs and SRT I also know that Cross in 64 Bit does not work with AsioDriver Pioneer

A pity that Mixvibes dropped us off to focus on App of Toys

Yes it's too bad...

I dont know if it's mixvibes or Pioneer, because the problem come from the Pioneer driver. I'm sure because when i start SERATO or TRAKTOR the driver panel recognize imediatly the phono timecode. this is not the case with mixvibes, so..

I found one person who have the same soundcard rooting problem on the Pioneer forum.
The Pioneer answer is funny, they advice the same configuration i describe before : turntable on line enter 1/2 & 3/4 and rooting the line enter on out 5/6, 7/8, so in this case you lose 2 channel on your mixer....

https://forums.pioneerdj.com/hc/en-us/c ... ng-Problem

I test with TRAKTOR SCRATCH and SERATO, that work perfectly, so i think i have the solution..

Hello,

One year later my last post, the mixvibes team support (or someone) know if the mixer DJM 900 NXS2 is finally compatible with Cross ?

Thanx !