MIXVIBES Dj Community old forum

Hi all.
I have quite a big problem for me, though it can breeze.
2 days ago I bought a set of cards MixVibes U46mk2.
I have windows 7
My problem is that the program does not see timecode.
I installed the drivers from the manufacturer ESI windows 7, the configuration consistent with the Install Wizard. Of course, everything on the card set to phono.
Previously, I played on the Maya44 USB and everything worked as God commanded.
When I turn monitoring can hear the squeak coming from the mixer, but does not see the MV signal at all, literally 0%. I also tried the drivers from the Download section, inputs and outputs respectively plugged, Vinyl new. System optimization for best performance also gave nothing.

Let me add that I downloaded the update to 7.4 from the Download section, here is the link:
Update Producer 7.4 RC1 & releases notes

I have a laptop Asus K72J
Processor: 4 x 2.4 GHz
Memory: 4GB RAM

Please help, greetings.

Sorry for my English. I used a translator. ^ ^

have you looked in the Producer section for any similiar problems and there solution,, you have been checking on the oter langauge fourms also,, not familiars with DVS and w7 to offere any assistance

you should post a config report will give thoes who know ,more info as to what happening/not happening

Hey,

can you see at DVS at the vinyl section an signal? or a flat line?
If no line then the input level is too high so decrease the volume to see the signal.

It is also helpful for us to get an config report when both players with vinyl control are running.
Please post this report here.

Thanks
Christian

There is flat line but no signal.


Config 2011/12/03 14:44

OS= build=7600 processor=PROCESSOR_IDENTIFIER=Intel64 Family 6 Model 37 Stepping 5, GenuineIntel
MixVibes Producer version=7.400 DLL langage=US version=7.400

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=Yes Equalization bypass=Yes
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=3 Nb Mixer=0
Managment Type ASIO
Device=MIXVIBES U46MK2 ASIO AsioVersion=0 DriverVersion=2
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=6
Managment Type ASIO
1-MIXVIBES U46 1/2:L 2-MIXVIBES U46 1/2:R
3-MIXVIBES U46 3/4:L 4-MIXVIBES U46 3/4:R
5-MIXVIBES U46 5/6:L 6-MIXVIBES U46 5/6:R

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:MIXVIBES U46 1/2:L-MIXVIBES U46 1/2:R
Mode=absolute
Riaa=Yes Preamp Left=0 db Preamp Right=0 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl 2 not connected
Vinyl 3 not connected
Vinyl 4 not connected



i have only one deck.

Hey,

how sounds the audio when you press bypass at DVS? can you hear the "piep" sound at your mixer?

is it loud or a low signal sound?

regards
Christian

yes, i hear 'piep'.
it's very loud.

ok when it is very loud go to the asio driver panel at your windows (in the task bar the ESI driver or MixVibes driver depends on what you have installed) and decrease the volume of the channel 1 of the inputs to 50% or more if it is not enough.

I have a question is it a Turntable with phono out or Line out? if it is line set the input to line and disable the RIAA option.

regards
Christian

Turntable is phono, I think. It's Technics 1200MK2.
OK, I Change volume to 50%.

But 'piep' is still loud

can you see know timecode signal at DVS? at the vinyl section?

And an other question how do you connected the turntable to the soundcard?

Regards
Christian