Page 1 of 1

[GELÖST]Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 10 Feb 2010, 22:35
by Macido
Hallo!

Ich benutze windows vista home premium und mixvibes dvs7 mit U-Mix44!
Bei mir wird nur eine timecode scheibe erkannt die rechte!
Die anzeige im programm zeigt aber dennoch eine bewegung auf dem linken die sehr langsam ist obwohl ich noch nicht mal ne nadel aufliegen habe! beim kalibrieren ist der rechte bei 100% der linke bei 0%!
Wäre echt cool wenn ihr mir helfen könntet!

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 11 Feb 2010, 00:10
by DJ4
Hey,

ist dein Linker turni richtig geerdet? Interessant wäre ein Konfigurationsreport.
Hast du auch den richtigen Eingang gewählt für deinen Timecode?
z.B: Channel 1 und 2 linkes laufwerk, Channel 3 u 4 rechtes Laufwerk.

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 11 Feb 2010, 00:21
by Macido
Config Report:
Config 2010/02/10 22:51

OS=Microsoft VISTA Service Pack 2 build=6002 processor=PROCESSOR_IDENTIFIER=x86 Family 6 Model 23 Stepping 10, GenuineIntel
MixVibes DVS version=7.218 DLL langage=DE version=7.210

System Setting
--------------------
Load in Ram Channel1= Yes Channel2= Yes
Load memory time limit=13 Load time=normal
Low gui priority=No Equalization bypass=No
MultiInstance=No

General Setting
--------------------
Nb Mixer Channels=2 Nb Samples=16
Windows Caption=No Theme=0
TAG V1=Yes TAG V2=Yes

Mix Setting
--------------------
AutoCue=Yes AutoGain=Yes AutoBpm at Load=Yes
Display Pitch=Yes Auto Match at load=No
Bpm Range min=78 max=150
Loop in bar boundaries=Yes Security=No History=Yes
Compressor=No Limiter=No

Sound Configuration
--------------------
Nb Sound=2 Nb Mixer=0
Managment Type ASIO
Device=MixvibesAsioUMix44 AsioVersion=0 DriverVersion=2
Latency=6 Driver sampling=44100 Nb Input=4 Nb Output=4
Managment Type ASIO
1-U-MIX44 Sound Device 1 2-U-MIX44 Sound Device 3
3-U-MIX44 Sound Device 2 4-U-MIX44 Sound Device 4

Vinyl Configuration
--------------------
Vinyl1 connected=vinyl version 2
Audio=ASIO source=0:U-MIX44 Sound Device 1-U-MIX44 Sound Device 2
Mode=absolute
Riaa=No Preamp Left=31 db Preamp Right=31 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.449 Volume max right=0.449 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000


Vinyl2 connected=vinyl version 2
Audio=ASIO source=2:U-MIX44 Sound Device 3-U-MIX44 Sound Device 4
Mode=absolute
Riaa=No Preamp Left=20 db Preamp Right=19 db Noise Filter=0 Hz
45T=No InverseLR=No PhaseInv=No
Decalage=0 ms Time limit=720000 ms
Silence seuil=-40.000 db SNR=40 db

Config Bypass Riaa=No Preamp=0 db Noise Filter=0 Hz Input Latency=0 ms

Vinyl Stats (turntable pitch set to 0 play at normal way)
Time code percent=0.500 Volume max left=0.000 Volume max right=0.000 Volume optimum=0.370
Speed Average(100ms)=0.000 Speed Average(1s)=0.000 Speed Average(3s)=0.000
Ich hab beide an der U-Mix geerdet oder kann ich auch einen am mixer erden? bei vinyl CD eingang sind nur 0:U-Mix... und 2:U-Mix zur auswahl

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 12 Feb 2010, 00:01
by Macido
hat jemand ein paar tips für mich?

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 12 Feb 2010, 13:06
by Blackbrook
Ich bin kein Profi beim Lesen der Config Reports, aber das sieht auf den ersten Blick für mich danach aus, als würde alles so laufen wie es soll :-/

Deine Aussage, dass sich der Timecode bewegt ohne das eine Nadel aufliegt heist für mich, dass da irgendwelche Rauschsignale am Kanal anliegen, die DVS als ganz langsamen Timecode interpretiert. Abhilfe schaffst du wenn du mal alle Kabel tauschst, eventuell sind welche nicht ordentlich abgeschirmt.

Viele Grüße,

Steve

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 12 Feb 2010, 23:29
by Macido
Hunderttausender Dank geht an dich!!! Ich habe das Master Kabel ausgetauscht und alle Kabel möglichs weit auseinader gelegt das sie sich nicht kreuzen oder so. Dazu noch die Boxen weiter vom Pult weg und nun laufen beide! Vielen Dank!

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 12 Feb 2010, 23:45
by Macido
Das mikrofon im Anschluss war der Störer. Ich habs grad ins U-Mix eingesteckt dann war alles wie vorher wieder raus funxt! naja muss ich halt schreien ;)

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 13 Feb 2010, 00:28
by Blackbrook
Das freut mich zu hören! Viel Spaß beim Mixen!!!

Grüße,

Steve

Re: Ich brauche hilfe es wird nur eine timecode erkannt!

PostPosted: 13 Feb 2010, 03:12
by Macido
Dankeschön - Laüft;)