Page 1 of 1

anyone using denon x600 for Vfx or Cross video

PostPosted: 09 Dec 2012, 15:03
by wazza
is anyone using the denon x600 for video mixing

I have been testing MIDI mapping with a denon x600 with Vfx demo

I'v been having some problems with the wave-form in mixvibes Vfx

every time I move the fader or a knobs fast, the waveforms freeze & the faders & knobs freeze the software for a second...audio & video is not effected...

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 09 Dec 2012, 15:58
by Hannes
The DNX600 is not very good, I had similar problems and also I couldnt get the Asio driver to work with Cross.

I think the Firmware of the DNX600 has some issues with Midi-signal sent. Imo the midi-stream is too busy and also affects the audio-stream.

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 09 Dec 2012, 18:26
by bigworm1063
I use the X600 with both Cross & Vfx and it works great for me. But then again, I've only mapped the faders. I haven't tried a full mapping yet. I've also found that it works better with Cross on my PC than my Mac.

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 14 Dec 2012, 20:17
by wazza
Ok thanks alot ...
After more testing ,with Cross DJ 1.7 demo .

The MIDI mapping in Cross works so much better than Vfx with the denon x600 , no fader freeze & smooth as butter

Not going to use the USB sound card part off the x600 as the denon asio drivers are S**T ...
I will use it as just the MIDI and as audio mixer ...going to use a e-box as a 4x4 sound card with the x600

Can I set the cross-fader in mixvibes Cross to do video only ???..
Can one turntable control both A&B decks in mixvibes Cross.???..

I would like to use my Roland mc 808 as a usb MIDI controller/ MIDI sequencer for the Cross sampler ...can I use the 16 fader on the 808 to control the volume off all the 16 pads in Cross ...one pad & one volume fader for each sample slot in Cross

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 15 Dec 2012, 01:29
by bigworm1063
Can I set the Cross-fader in MixVibes Cross to do video only ???..

Yes.

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 15 Dec 2012, 04:39
by daniel clark
:cool: :cool: :eek: wazza ,,you might want to look at this thread :eek:
viewtopic.php?f=346&t=26031&start=10

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 15 Dec 2012, 05:05
by wazza
After using the magic search button :neutral: ;)
Seam like ,All I have to do is MIDI map a button on the mixer to switch from one deck to the other using one turntable...NICE..

If your not able to MIDI map the volume off each sample slot/pad in Cross that's no biggy ...can alway use 808 fader for other things in Cross like EFX's


Might be time for me to cash in some off that Karma I have been hoarding for Christmas

Re: anyone using denon x600 for Vfx or Cross video

PostPosted: 15 Dec 2012, 05:28
by daniel clark
:cool: :cool: kool ,,not shure if your looking at the vid plug in also,,check the posting on it ,,can trade k for it also :cool: :cool:
viewtopic.php?f=259&t=25940
viewtopic.php?f=259&t=10078

links for info above