Beginner-Problem with DVS7

[Reversah]

Hello,i know about the wrong section of the topic,but is the only i can make a topic.
So,i 'm a new user of MixVibes DVS7 system.I do the install but i'm lost in the input/output setting.
Anyone want to help like a step-to step configuration?

Any help will be appreciated,Thanks.

[christiankoopmann]

Hey,

welcome and to your first Problem that you can't post at other sections do the following steps:
First delete all Cookies from mixvibes by clicking at this link:
After that please log in again and check if you can now create a thread at the Support section.
If not please write here again.
To your second question. Have you looked at the Manuel which Comes with DVS? I will check if I can create a Little step by step manuel how to connect the devices.
But for that please give us some Information about what exactly you have as Hardware.

But first you have to install the Driver for your soundcard. After that plug the device in and wait for installing the complete Driver. Than you connect the Player A or (deck left) from your CD or Turntable to the INPUT 1/2 of the U-Mix44, next you do this also with the Deck B so the right CD or turntable to the INPUT 3/4. After that you connect the OUTPUT 1/2 to Channel 1 from your mixer. Do the same with OUTPUT 3/4 to Channel 2.
Now you Need to start DVS and go to the preferences and start calibrating. Please run the CD or turntable so the DVS can calibrate the Inputs.

If oyu Need more inforamtion please give us Details where you have Problems.
regards
Christian

[Reversah]

Thanks for the response.
I delete the cookies,i can write on other sections but still not on the support section.

To the subject.
Turntable:Numark tt200 x1
Mixer:Numark m101
Needle:Shure m44-7
OS:Windows 7 Ultimate x64
Soundcard:U mix44
I connect the outpout (phono) of turnatble on input of the soundcard.
Then,i connect the output of soundcard on Line in of channel 1 in the mixer.And the soundcard to PC via usb.
I think i dont done the asio & control panel settings right,i follow the manual but it's a little bit different from the xp windows.I forgot to say that i have simple 2.1 PC speakers connect via the usual green cable on the PC soundcard.

Thanks for your interest

[christiankoopmann]

Hey,

okay normaly you should be able to create a thread at the Support section if you deleted the Cookies. I will look and check this.

To the subject:
Okay, you Need to connect the Mixer M101 with your Speaker System. You can't use the internal soundcard to route your Sound to your Speakers.
Currently I'm at vacation and have no Access to my Computer where DVS is still installed to create screenshots how the Output Routine should be done. but maybe we can do this by writing.
You Need to select ASIO U-Mix44 and then set Inputs and Outputs to the specific Parameters.

regards
Christian

[Reversah]

You Need to select ASIO U-Mix44 and then set Inputs and Outputs to the specific Parameters.On control panel sound settings?

In what hub on the mixer i connect the speakers?
I have only mic and headphones.The speakers have the classic 3.5mm jack cable.

[christiankoopmann]

You connect the Master Out of your Mixer with the 3.5 jack. So you need a chinch to 3.5mm clinke cable to connect mixer with your speakers.

Regards
Christian

[Reversah]

Thanks for you help.I aprreciate tha you on vacation and you help me the same time.

Well,The master is L/R os i need i adaptor right?

And..i buy DVS for scratcing and listen music from my PC at the same time.Is this gonna be possible if i connect the speakers to the mixer?
And please,can you send me a link of the clinke you said?

[christiankoopmann]

Mixing and hearing music the same time? I can't to both the same time

What speaker system has you? Than I could check what exactly you need.

Regards
Christian

[Reversah]

http://www.plaisio.gr/ypologistes-anava ... 1-M200.htm

Without DVS,i use to scratch and listen the scratch & the instrumental at the same time.

[christiankoopmann]

How do you use the system currently? Hearing the instrumental and scratch means that you run two virtual players at the computer and scratch with the computer??

Sorry to ask this stupid questions but currently I have no clue how you currently use the system and how you want to use DVS.

To DVS: you have two outputs so for every payer at DVS (deck a and b) you have an output which would be mixed at your mixer which is connected to your speakers.
So you would have at deck a or b the instrumental sound and on the other deck the sound you want to scratch.
The mixed sound will be than from the master out of the mixer to the input of your soundsystem.
So you will need a cable like the one you have between the computer and the soundsystem but at one side you need a cinch cable. I will check if I can find a picture of what I mean. And please give me feedback a lute if I understand how you want to use the system.

Regards
Christian